HC MECO Seal

The MECO HC seal model is the best air-free choice in sealing technology for screw conveyors . The HC model is a full-contact, soft-face mechanical shaft seal, using an elastomer drive to rotate bearing-grade, polymeric seal faces against fixed, stainless steel seal faces. The various seal assemblies are sized for equipment following standards of the Conveyor Equipment Manufacturers Association (C.E.M.A.) and their metric equivalents.

The HC Seal model provides the superior performance, durability and quality of workmanship that are hallmarks of MECO’s many other highly-regarded custom seals.

HC MECO Seal Datahseet FTL
The MECO HC Seal model is ideal for screw conveyors/scrolls, small blenders, bucket elevators, and similar rotating equipment used in bulk process industries. The HC Seal model is used on horizontal, inclined and vertical shafts for unsplit installations.
The HC Seal replaces standard waste pack housings. It is made with a heavy, metal or FDA nylon housing that cannot be crushed by an over-tightened flange bearing. Two replaceable stainless steel stationary seal faces attach to the seal housing. Inside is a rotating seal face assembly, consisting of replaceable rotors and drive elastomer. The elastomer and rotors interlock, forming an air and watertight seal. The low-friction rotating seal faces are at right angles to the shaft and in full contact with the stationary seal faces. Around the driving elastomer is a stainless steel hose clamp to provide seal face loading. The seal is vented to atmosphere at an effective location to monitor seal performance.
The HC model seal is stocked in 6 standard inch and 10 metric sizes. These 16 seals can be easily converted for other shaft sizes and all fit within the 6 stocked housing (HSG) sizes. This allows the HC model seals to be sized for shaft diameters 5.07” (129mm) and smaller. See the Stocked HSG# Chart below for maximum shaft size for each of the six housings.
The HC seal’s rugged housing options are designed for long life. You may choose from three stock housing materials: FDA Nylon, Anodized Aluminum or 316L SS. Three elastomer materials, Viton, FDA white silicone or EPDM, ensure compatibility with nearly all applications. The standard stators are type 304 stainless steel. The standard rotors are MECO3000, a high-performance, bearing grade, polymer- filled PTFE with FDA approval. No abrasive filler material is added to MECO3000. MECO3120, a white, FDA approved, ceramic filled, PTFE is available as an option for processes where maximum wear resistance is needed. Any of the components may be individually replaced. Unsplit rebuild kits consisting of replacement rotors and drive elastomer are maintained in-stock for immediate shipment. In cases where it is difficult to remove the bearing or drive, convenient, fully-split rebuild kits are available. Since Woodex’s MECO Seal division manufactures many custom shaft seals, they have the capability to fabricate from any material when required. See Sizing Chart below for dimensional information.
Stocked HSG# Each MECO HC Seal housing can accommodate optional shafts up to these limits:
HSG # Max. Shaft ø
1 1.77"/45mm
2 2.24"/57mm
3 2.63"/67mm
4 3.62"/92mm
5 4.07"/103mm
6 5.07"/129mm
C.E.M.A Standard Sizes (inches)
CEMA Part #
øA shaft P HSG # SQ MIN SQ MAX W øC MIN øC MAX
HCZ1W4A150
1.50 5.38 1 4.00 4.38 5/8 5.65 6.19
HCZ2W4A200
2.00 6.50 2 4.38 5.38 3/4 6.19 7.60
HCZ3W4A244
2.44 7.38 3 5.13 6.25 3/4 7.25 8.84
HCZ4W4A300
3.00 7.75 4 5.75 6.50 7/8 8.12 9.19
HCZ5W4A344
3.44 9.25 5 6.75 8.00 7/8 9.55 11.31
HCZ6W4A444
4.44 10.88 6 7.75 8.75 7/8 10.96 12.38
HCZ6W4A444
4.44 10.88 6 7.75 8.75 7/8 10.96 12.38
METRIC Standard Sizes (millimeters)
Metric Part # øA shaft P HSG # SQ MIN SQ MAX W øC MIN øC MAX
HCZ1W4A157/177
40/45
137 1 102 111 16 144 157
HCZ2W4A197/217
50/55 165 2 111 137 19 157 193
HCZ3W4A236/256
60/65 187 3 130 159 19 184 225
HCZ4W4A276 70 197 4 146 165 22 206 233
HCZ4W4A295
75 197 4 146 165 22 206 233
HCZ4W4A315 80 197 4 146 165 22 206 233
HCZ5W4A335 85 235 5 171 203 22 243 287
HCZ5W4A354 90 235 5 171 203 22 243  287 
HCZ6W4A394 100 276 6 197 222 24 278 314
HCZ6W4A433 110 276 6 197 222 24 278 314
Rotor Material Process Conditions HCZ - Anodized Alum. Housing HCP - FDA Nylon Housing HCS - 316L Stainless Housing
MECO3000
(recommended)
TEMPERATURE
-60 to 500°F (-50 to 260°C)
-35 to 200°F (-37 to 94°C)
-60 to 500°F (-50 to 260°C)
PRESSURE
Vacuum to 10 psig (70 kPa)
Vacuum to 10 psig (70 kPa)
Vacuum to 10 psig (70 kPa)
SPEED
to 150 RPM
to 100 RPM to 150 RPM
UHMW TEMPERATURE
-178 to 135°F (-117 to 57°C)
-35 to 135°F (-37 to 57°C)
-178 to 135°F (-117 to 57°C)
PRESSURE Vacuum to 5 psig (35 kPa)  Vacuum to 5 psig (35 kPa)
Vacuum to 5 psig (35 kPa)
SPEED to 50 RPM to 50 RPM to 50 RPM
Mechanical Capabilities: 1/64" Axial Motion
Silicone Elastomer -178 to 500°F (-117 to 260° C) 
1/4" T.I.R. Runout
Viton Elastomer -75 to 450°F (-59 to 232° C)
1/2" Thermal Growth
EPDM Elastomer -70 to 325°F (-56 o 163°C) 
Results may vary with operating conditions and shaft ø - please call for discussion.